A Nema 17 stepper motor is a stepper motor with a 1.7 x 1.7 inch (42 x 42mm) faceplate. Nema 17 high torque stepper motors provide great value with no quality sacrifice. The version with a step angle of 0.9° is more precise than the typical 1.8° version of the motor. These motors are engineered to provide the highest possible torque but minimize vibration and audible noise. A wide range of motor windings and stack lengths are readily available, or the motors can be customized to meet your machine requirements. We can also have the windings customized to perfectly match your voltage, current and maximum torque at operating speeds.

NEMA stepper motor sizes depend on the frame size of the stepper motor. NEMA means the standards set by “National Electrical Manufacturers Association”, which is comprised of 560 major electrical manufacturers in the United States, primarily consisting of manufacturers of equipment and devices for power generation, transmission, distribution, and power applications. The purpose of standard setting is to eliminate misunderstandings between electrical product manufacturers and users and to specify the safety of these product applications.

Specifications:

• Stepper Motor Height: 40mm
• Shaft size: 5mm
• Steps per revolution: 200
• Operating Temperature: -10 to 40 °C
• Unipolar Holding Torque: 22.2 oz-in

Package Include:

• 1 x XYSLDJ Stepper Motor

The 28BYJ-48 is a small, 12 volt geared stepping motors. These stepping motors are apparently widely used to control things like automated blinds, A/C units and are mass produced. Due to the gear reduction ratio of approximately 64:1 it offers decent torque for its size at speeds of about 15 rotations per minute (RPM).

The motor can be used together with all stepper motor drivers for unipolar motors. The red wire should then be connected to ground (GND), orange/pink to M1 (or similar) and blue/yellow to M2 (or similar). Can also easily be driven by discrete transistors or a darlington driver (ULN2003).

5 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2 development board used for. supporting the use of a direct plug and easy to use stepper motor used in the development board. Stepper motor driver board with ULN2003 A, B, C, D four-phase LED indicates the status of the stepper motor work Stepper motor with a standard interface, when used directly pluggable

Specifications:

• Motor Model : 28BYJ-48
• Rated Voltage: DC 12V 4 Phase
• Step Angle: 5.625x 1/64
• No-Load Pull-In Frequency: > 600Hz
• No-Load Pull-Out Frequency: > 1000Hz
• Pulling Torque: > 34.3mN.M (120Hz)
• Brake Torque: > 34.3mN.M
• DC Resistance: 200Ω±7% (25C)
• Insulation Resistance: >10MΩ (500V)
• Dielectric Strength: 600V AC / 1mA / 1s
• Insulation Class: A
• Temperature Rise: <40K (120Hz)
• Noise: <40dB (120Hz, No Load, 10cm)
• Driver: ULN2003
• Weight: 50g

Features:

• DC 12V 4-Phase Stepper Motor + Driver Test Module Board For Arduino
• The Driver Board Has A, B, C, D Four-Phase LEDs To Indicate The Working State Of The Stepper Motor
• Stepper Motor With Standard Interface, Can Be Directly Plugged And Used
• Durable And Reliable
• 100% Brand New And High Quality
• The rotation angle of the motor is proportional to the input pulse.
• The motor has full torque at standstill(if the windings are energized)
• Precise positioning and repeatability of movement since good stepper motors have an accuracy of – 5% of a step and this error is non cumulative from one step to the next.
• Excellent response to starting/stopping/reversing.
• Very reliable since there are no contact brushes in the motor. Therefore the life of the motor is simply dependent on the life of the bearing.
• The motors response to digital input pulses provides open-loop control, making the motor simpler and less costly to control.
• It is possible to achieve very low speed synchronous rotation with a load that is directly coupled to the shaft.
• A wide range of rotational speeds can be realized as the speed is proportional to the frequency of the input pulses.

Applications:

• Supporting the use of a direct plug and easy to use stepper motor used in the development board.
• Stepper motor driver board with ULN2003
• A, B, C, D four-phase LED indicates the status of the stepper motor work
• Stepper motor with a standard interface, when used directly pluggable

Note:

• 1.Due To The Manual Measurement And Different Measurement Methods, Please Allow 2-3mm Deviation.
• 2.Please Be Reminded That Due To Lighting Effects And Monitor’ S Brightness/Contrast Settings Etc, The Color Tone Of The Website’ S Photo And The Actual Item Could Be Slightly Different

Package Included:

• 1 x Stepper Motor DC 12V 28BYJ-48 4 Phase 5 Wires With ULN2003 Driver Board Programmable Small Reduction Gear Motor

The 28BYJ-48 is a small, 5 volt geared stepping motors. These stepping motors are apparently widely used to control things like automated blinds, A/C units and are mass produced. Due to the gear reduction ratio of approximately 64:1 it offers decent torque for its size at speeds of about 15 rotations per minute (RPM).

The motor can be used together with all stepper motor drivers for unipolar motors. The red wire should then be connected to ground (GND), orange/pink to M1 (or similar) and blue/yellow to M2 (or similar). Can also easily be driven by discrete transistors or a darlington driver (ULN2003).

5 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2 development board used for. supporting the use of a direct plug and easy to use stepper motor used in the development board. Stepper motor driver board with ULN2003 A, B, C, D four-phase LED indicates the status of the stepper motor work Stepper motor with a standard interface, when used directly pluggable

Specifications:

• Motor Model : 28BYJ-48
• Rated Voltage: DC 5V 4 Phase
• Step Angle: 5.625x 1/64
• No-Load Pull-In Frequency: > 600Hz
• No-Load Pull-Out Frequency: > 1000Hz
• Pulling Torque: > 34.3mN.M (120Hz)
• Brake Torque: > 34.3mN.M
• DC Resistance: 200Ω±7% (25C)
• Insulation Resistance: >10MΩ (500V)
• Dielectric Strength: 600V AC / 1mA / 1s
• Insulation Class: A
• Temperature Rise: <40K (120Hz)
• Noise: <40dB (120Hz, No Load, 10cm)
• Driver: ULN2003
• Weight: 50g

Features:

• DC 5V 4-Phase Stepper Motor + Driver Test Module Board For Arduino
• The Driver Board Has A, B, C, D Four-Phase LEDs To Indicate The Working State Of The Stepper Motor
• Stepper Motor With Standard Interface, Can Be Directly Plugged And Used
• Durable And Reliable
• 100% Brand New And High Quality
• The rotation angle of the motor is proportional to the input pulse.
• The motor has full torque at standstill(if the windings are energized)
• Precise positioning and repeatability of movement since good stepper motors have an accuracy of – 5% of a step and this error is non cumulative from one step to the next.
• Excellent response to starting/stopping/reversing.
• Very reliable since there are no contact brushes in the motor. Therefore the life of the motor is simply dependent on the life of the bearing.
• The motors response to digital input pulses provides open-loop control, making the motor simpler and less costly to control.
• It is possible to achieve very low speed synchronous rotation with a load that is directly coupled to the shaft.
• A wide range of rotational speeds can be realized as the speed is proportional to the frequency of the input pulses.

Applications:

• Supporting the use of a direct plug and easy to use stepper motor used in the development board.
• Stepper motor driver board with ULN2003
• A, B, C, D four-phase LED indicates the status of the stepper motor work
• Stepper motor with a standard interface, when used directly pluggable

Note:

• 1.Due To The Manual Measurement And Different Measurement Methods, Please Allow 2-3mm Deviation.
• 2.Please Be Reminded That Due To Lighting Effects And Monitor’ S Brightness/Contrast Settings Etc, The Color Tone Of The Website’ S Photo And The Actual Item Could Be Slightly Different

Package Included:

• 1 x Stepper Motor DC 5V 28BYJ-48 4 Phase 5 Wires With ULN2003 Driver Board Programmable Small Reduction Gear Motor

12V Stepper Motor DC 12V 28BYJ-48 4 Phase 5 Wires Programmable Small Reduction Gear Stepper Motor Compatible With Arduino DIY Project 3D Printer Parts

A stepper motor is an electro mechanical device which converts electrical pulses into discrete mechanical movements. The shaft or spindle of a stepper motor rotates in discrete step increments when electrical command pulses are applied to it in the proper sequence. The motor’s rotation has several direct relationships to these applied input pulses. The sequence of the applied pulses is directly related to the direction of motor shafts rotation. The speed of the motor shafts rotation is directly related to the frequency of the input pulses and the length of rotation is directly related to the number of input pulses applied. One of the most significant advantages of a stepper motor is its ability to be accurately controlled in an open loop system. Open loop control means no feedback information about the position is needed. This type of control eliminates the need for expensive sensing and feedback devices such as optical encoders. Your position is known simply by keeping track of the input step pulses.

The 28BYJ-48 is a small, 12 volt geared stepping motors. These stepping motors are apparently widely used to control things like automated blinds, A/C units and are mass produced. Due to the gear reduction ratio of approximately 64:1 it offers decent torque for its size at speeds of about 15 rotations per minute (RPM).

The motor can be used together with all stepper motor drivers for unipolar motors. The red wire should then be connected to ground (GND), orange/pink to M1 (or similar) and blue/yellow to M2 (or similar). Can also easily be driven by discrete transistors or a darlington driver (ULN2003).

Specifications:

• Model : 28BYJ-48
• Main Material: Metal, Plastic
• Rated voltage : 12VDC
• Number of Phase : 4
• Speed Variation Ratio : 1/64
• Stride Angle : 5.625° /64
• Frequency : 100Hz
• DC resistance : 50Ω±7%(25°C)
• Idle In-traction Frequency : > 600Hz
• Idle Out-traction Frequency : > 1000Hz
• In-traction Torque >34.3mN.m(120Hz)
• Self-positioning Torque >34.3mN.m
• Friction torque : 600-1200 gf.cm
• Pull in torque : 300 gf.cm
• Insulated resistance >10MΩ(500V)
• Insulated electricity power :600VAC/1mA/1s
• Insulation grade :A
• Rise in Temperature <40K(120Hz)
• Noise <35dB(120Hz,No load,10cm)
• Output shaft: 5mm flat
• Dimensions: ø28 x 19mm
• Mount Hole Diameter: 4mm
• Mounting Hole Distance: 35mm
• Weight: 36g

Features：

• High-quality stepper motor with gear reduction, low noise and smooth operation. Provide with five wires and four coils and 1/64 gear reduction.
• The stepper motor can be used for ordinary ULN2003 driver board, connect to the 2 phase, support the development board.
• 12V can be driven, which is convenient for MCU developers. An open interface can also be used to drive other stepper motors through this board.
• Applicable to various platforms such as 51/AVR/AVR/ARM. Great stepper motors for your DIY project such as robot design.
• Suitable for single-chip learning machine learning or air conditioning windshield drive and security camera monitoring adjustment direction drive.

Applications:

• Air Conditioner Louver
• Small Cooling / Heating Fan

Package Include:

• 1 x Stepper Motor DC 12V 28BYJ-48 4 Phase 5 Wires Programmable Small Reduction Gear Stepper Motor

0.3N.m NEMA17 NEMA-17 17HS3401 DC 12V 1.3A 0.25N.m 1.8 Degree 4 Lead Cables 42BYGH L34mm Stepper Motor For CNC Machine 3D Printer NEMA 17 Stepper Motor

A stepper motor to satisfy all your 3D-Printer, robotics, Linear Motion projects needs! This 4-wire bipolar stepper has 1.7? per step for smooth motion and a nice holding torque. This motor was specified to have a max current of 1.7A/phase so that it could be driven easily with common motor shield for Arduino (or other motor driver) and a wall adapter or lead-acid battery. The motors are supplied with a 30cm long power cable with a 4-pin female connector

This powerful 17HS3401 stepper motor is perfect for 3D printers, CNC machines or simply for mechanical Arduino projects. If you want to operate the stepper motor with the Arduino, we recommend buying an A4988, DRV8825 or TMC2208 driver.

NEMA 17 17HS3401 DC 12v 1.3A 0.25N.m 1.8 Degree 4 Pin Cable 42 BYGH 34mm Stepper Motor For CNC LASER Engraving Machine 3D Printer Extruder Accessories

Specification:

• Name : Stepper Motor
• Model: 17HS3401
• Wiring Configuration: 4-Wire Bipolar
• Actual Rated Input Voltage: 12-24VDC
• Holding Torque: 0.25Nm
• Current Type: DC
• Rated Current : 1.3A
• Resistance per Phase: 30Ω±10%
• Full Step Angle: 1.8° Degree
• Nominal Rated Input Voltage: 24 V, 12 V
• Step angle accuracy: + – 5% (full step, not load)
• Resistance accuracy: + – 10%
• Inductance accuracy: + – 20%
• Temperature rise: 80deg Max (rated current, 2 phase on)
• Ambient temperature: 20deg ~ +50deg
• Insulation resistance: 100MΩ Min, 500VDC
• Insulation Strength: 500VAC for one minute
• Motor Dimension Size: 42x42x34mm
• Shaft Length: 22mm
• Shaft Diameter: 5mm
• Motor Weight: 220gm

Features:

• Low noise.
• Low heat.
• Smooth operation.
• Good acceleration performance.
• The use of advanced technology reduces noise.
• Reduced automatic errors caused by the use of reduction gears.
• Made of high quality alloy material, durable and long service.
• The motor adopt 4 pin cable outlet method, easy to connect.
• Adopting high quality motor steel material, with high torque, low self-inductance reactance, responsive and can avoid system error.
• There is rotor rubber covering the rotor, effectively reduce the noise.
• Our mini motor uses high hardness metal, tough and durable. And the matte texture in the side wall can increase friction.
• Small size, convenient storage and placement.

Connection:

• Red: A+
• Green: A-
• Yellow: B+
• Blue: B-

Applications:

• This small motors can be used in various area, such as stage lighting; laser engraving; textile machinery; medical equipment; placement machine; non-standard equipment; 3D printer; automation equipment, and etc.
• Widely used in 3D printers, surveillance equipment, textile / packaging machinery and stage lighting, etc.

Package Include:

• 1 x 0.3N.m NEMA17 NEMA-17 17HS3401 DC 12V 1.3A 0.25N.m 1.8 Degree 4 Lead Cables 42BYGH L34mm Stepper Motor For CNC Machine 3D Printer NEMA 17 Stepper Motor

5V 28BYJ-48 Stepper Motor DC 5V 28BYJ-48 4 Phase 5 Wires Programmable Small Reduction Gear Stepper Motor Drive Compatible With Arduino Electronics Circuitry & Parts

A stepper motor is an electro mechanical device which converts electrical pulses into discrete mechanical movements. The shaft or spindle of a stepper motor rotates in discrete step increments when electrical command pulses are applied to it in the proper sequence. The motor’s rotation has several direct relationships to these applied input pulses. The sequence of the applied pulses is directly related to the direction of motor shafts rotation. The speed of the motor shafts rotation is directly related to the frequency of the input pulses and the length of rotation is directly related to the number of input pulses applied. One of the most significant advantages of a stepper motor is its ability to be accurately controlled in an open loop system. Open loop control means no feedback information about the position is needed. This type of control eliminates the need for expensive sensing and feedback devices such as optical encoders. Your position is known simply by keeping track of the input step pulses.

The 28BYJ-48 is a small, 5 volt geared stepping motors. These stepping motors are apparently widely used to control things like automated blinds, A/C units and are mass produced. Due to the gear reduction ratio of approximately 64:1 it offers decent torque for its size at speeds of about 15 rotations per minute (RPM).

The motor can be used together with all stepper motor drivers for unipolar motors. The red wire should then be connected to ground (GND), orange/pink to M1 (or similar) and blue/yellow to M2 (or similar). Can also easily be driven by discrete transistors or a darlington driver (ULN2003).

Specifications:

• Model : 28BYJ-48
• Main Material: Metal, Plastic
• Rated voltage : 5VDC
• Number of Phase : 4
• Speed Variation Ratio : 1/64
• Stride Angle : 5.625° /64
• Frequency : 100Hz
• DC resistance : 50Ω±7%(25°C)
• Idle In-traction Frequency : > 600Hz
• Idle Out-traction Frequency : > 1000Hz
• In-traction Torque >34.3mN.m(120Hz)
• Self-positioning Torque >34.3mN.m
• Friction torque : 600-1200 gf.cm
• Pull in torque : 300 gf.cm
• Insulated resistance >10MΩ(500V)
• Insulated electricity power :600VAC/1mA/1s
• Insulation grade :A
• Rise in Temperature <40K(120Hz)
• Noise <35dB(120Hz,No load,10cm)
• Output shaft: 5mm flat
• Dimensions: ø28 x 19mm
• Mount Hole Diameter: 4mm
• Mounting Hole Distance: 35mm
• Weight: 36g

Features：

• High-quality stepper motor with gear reduction, low noise and smooth operation. Provide with five wires and four coils and 1/64 gear reduction.
• The stepper motor can be used for ordinary ULN2003 driver board, connect to the 2 phase, support the development board.
• 5V can be driven, which is convenient for MCU developers. An open interface can also be used to drive other stepper motors through this board.
• Applicable to various platforms such as 51/AVR/AVR/ARM. Great stepper motors for your DIY project such as robot design.
• Suitable for single-chip learning machine learning or air conditioning windshield drive and security camera monitoring adjustment direction drive.

Applications:

• Air Conditioner Louver
• Small Cooling / Heating Fan

Package Include:

• 1 x Stepper Motor DC 5V 28BYJ-48 4 Phase 5 Wires Programmable Small Reduction Gear Stepper Motor

0.55N.m NEMA17 17HS8401 DC 12V 1.7A 0.55N.m 1.8 Degree 6 Pin Cables 42BYGH L48mm NEMA 17 Stepper Motor For 3D Printer CNC Machine Stepper Motor NEMA 17 Stepper Motor 12V

A stepper motor to satisfy all your 3D-Printer, robotics, Linear Motion projects needs! This 6-wire bipolar stepper has 1.7? per step for smooth motion and a nice holding torque. This motor was specified to have a max current of 1.7A/phase so that it could be driven easily with common motor shield for Arduino (or other motor driver) and a wall adapter or lead-acid battery. The motors are supplied with a 30cm long power cable with a 6-pin female connector

This powerful 17HS8401 stepper motor is perfect for 3D printers, CNC machines or simply for mechanical Arduino projects. If you want to operate the stepper motor with the Arduino, we recommend buying an A4988, DRV8825 or TMC2208 driver.

NEMA 17 17HS8401 DC 12v 1.7A 0.55N.m 1.8 Degree 6 Pin Cable 42BYGH 47mm Stepper Motor For CNC LASER Engraving Machine 3D Printer Extruder Accessories

Specification:

• Name : Stepper Motor
• Model: 17HS8401
• Wiring Configuration: 4-Wire Bipolar
• Actual Rated Input Voltage: 12-24VDC
• Holding Torque: 0.55Nm
• Current Type: DC
• Rated Current : 1.7A
• Resistance per Phase: 30Ω±10%
• Full Step Angle: 1.8° Degree
• Nominal Rated Input Voltage: 24 V, 12 V
• Step angle accuracy: + – 5% (full step, not load)
• Resistance accuracy: + – 10%
• Inductance accuracy: + – 20%
• Temperature rise: 80deg Max (rated current, 2 phase on)
• Ambient temperature: 20deg ~ +50deg
• Insulation resistance: 100MΩ Min, 500VDC
• Insulation Strength: 500VAC for one minute
• Motor Dimension Size: 42x42x47mm
• Shaft Length: 22mm
• Shaft Diameter: 5mm
• Motor Weight: 375gm

Features:

• Low noise.
• Low heat.
• Smooth operation.
• Good acceleration performance.
• The use of advanced technology reduces noise.
• Reduced automatic errors caused by the use of reduction gears.
• Made of high quality alloy material, durable and long service.
• The motor adopt 4 pin cable outlet method, easy to connect.
• Adopting high quality motor steel material, with high torque, low self-inductance reactance, responsive and can avoid system error.
• There is rotor rubber covering the rotor, effectively reduce the noise.
• Our mini motor uses high hardness metal, tough and durable. And the matte texture in the side wall can increase friction.
• Small size, convenient storage and placement.

Connection:

• Red: A+
• Green: A-
• Yellow: B+
• Blue: B-

Applications:

• This small motors can be used in various area, such as stage lighting; laser engraving; textile machinery; medical equipment; placement machine; non-standard equipment; 3D printer; automation equipment, and etc.
• Widely used in 3D printers, surveillance equipment, textile / packaging machinery and stage lighting, etc.

Package Include:

• 1 x NEMA 17 17HS8401 DC 12v 1.7A 0.55N.m 1.8 Degree 6 Pin Cable 42BYGH 47mm Stepper Motor

0.45N.m NEMA17 17HS4401 DC 12V 1.3A 0.45N.m 1.8 Degree 4 Pin Cables 42BYGH L40mm NEMA 17 Stepper Motor For 3D Printer CNC Machine Stepper Motor NEMA 17 Stepper Motor 12V

A stepper motor to satisfy all your 3D-Printer, robotics, Linear Motion projects needs! This 4-wire bipolar stepper has 1.7? per step for smooth motion and a nice holding torque. This motor was specified to have a max current of 1.7A/phase so that it could be driven easily with common motor shield for Arduino (or other motor driver) and a wall adapter or lead-acid battery. The motors are supplied with a 30cm long power cable with a 4-pin female connector

This powerful 17HS4401 stepper motor is perfect for 3D printers, CNC machines or simply for mechanical Arduino projects. If you want to operate the stepper motor with the Arduino, we recommend buying an A4988, DRV8825 or TMC2208 driver.

NEMA 17 17HS4401 DC 12v 1.7A 0.45N.m 1.8 Degree 4 Pin Cable 42BYGH 40mm Stepper Motor For CNC LASER Engraving Machine 3D Printer Extruder Accessories

Specification:

• Name : Stepper Motor
• Model: 17HS4401
• Wiring Configuration: 4-Wire Bipolar
• Actual Rated Input Voltage: 12-24VDC
• Holding Torque: 0.45Nm
• Current Type: DC
• Rated Current : 1.7A
• Resistance per Phase: 30Ω±10%
• Full Step Angle: 1.8° Degree
• Nominal Rated Input Voltage: 24 V, 12 V
• Step angle accuracy: + – 5% (full step, not load)
• Resistance accuracy: + – 10%
• Inductance accuracy: + – 20%
• Temperature rise: 80deg Max (rated current, 2 phase on)
• Ambient temperature: 20deg ~ +50deg
• Insulation resistance: 100MΩ Min, 500VDC
• Insulation Strength: 500VAC for one minute
• Motor Dimension Size: 42x42x40mm
• Shaft Length: 22mm
• Shaft Diameter: 5mm
• Motor Weight: 300gm

Features:

• Low noise.
• Low heat.
• Smooth operation.
• Good acceleration performance.
• The use of advanced technology reduces noise.
• Reduced automatic errors caused by the use of reduction gears.
• Made of high quality alloy material, durable and long service.
• The motor adopt 4 pin cable outlet method, easy to connect.
• Adopting high quality motor steel material, with high torque, low self-inductance reactance, responsive and can avoid system error.
• There is rotor rubber covering the rotor, effectively reduce the noise.
• Our mini motor uses high hardness metal, tough and durable. And the matte texture in the side wall can increase friction.
• Small size, convenient storage and placement.

Connection:

• Red: A+
• Green: A-
• Yellow: B+
• Blue: B-

Applications:

• This small motors can be used in various area, such as stage lighting; laser engraving; textile machinery; medical equipment; placement machine; non-standard equipment; 3D printer; automation equipment, and etc.
• Widely used in 3D printers, surveillance equipment, textile / packaging machinery and stage lighting, etc.

Package Include:

• 1 x NEMA 17 17HS4401 DC 12v 1.7A 0.45N.m 1.8 Degree 4 Pin Cable 42 BYGH 40mm Stepper Motor