SMD Arduino Uno R3 Development Board SMD Chip Version Microcontroller Based On ATmega328 With USB Cables Arduino Uno Starter Kit For Electronics Projects

Description: Best Quality Arduino Uno R3 

The Arduino Uno SMD is a version of the Arduino Uno, but uses an surface mount version of the Atmega328P instead of the through-hole version. This version was made in response to a shortage in supply of the through-hole Atmega328P. The board is based on the ATmega328 ).

It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8U2 programmed as a USB-to-serial converter.

“Uno” means one in Italian and is named to mark the upcoming release of Arduino 1.0. The Uno and version 1.0 will be the reference versions of Arduino, moving forward. The Uno is the latest in a series of USB Arduino boards, and the reference model for the Arduino platform; for a comparison with previous versions, see the index of Arduino boards

Specification:

• Microcontroller ATmega328P
• Operating Voltage 5V
• Input Voltage (recommended) 7-12V
• Input Voltage (limit) 6-20V
• Digital I/O Pins 14 (of which 6 provide PWM output)
• PWM Digital I/O Pins 6
• Analog Input Pins 6
• DC Current per I/O Pin 20 mA
• DC Current for 3.3V Pin 50 mA
• Flash Memory 32 KB (ATmega328P) of which 0.5 KB used by bootloader
• SRAM 2 KB (ATmega328P)
• EEPROM 1 KB (ATmega328P)
• Clock Speed 16 MHz
• LED_BUILTIN 13
• Length 68.6 mm
• Width 53.4 mm
• Weight 25 g

The power pins are as follows:

• VIN: The input voltage to the Arduino board when it’s using an external power source (as opposed to 5 volts from the USB connection or other regulated power source). You can supply voltage through this pin, or, if supplying voltage via the power jack, access it through this pin.
• 5V: The regulated power supply used to power the microcontroller and other components on the board. This can come either from VIN via an on-board regulator, or be supplied by USB or another regulated 5V supply.
• 3V3: A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 50 mA.
• GND: Ground pins.

Memory:

• The ATmega328 has 32 KB (with 0.5 KB used for the bootloader). It also has 2 KB of SRAM and 1 KB of EEPROM (which can be read and written with the EEPROM library).

Input and Output:

Each of the 14 digital pins on the Uno can be used as an input or output, using pinMode(), digitalWrite(), and digita lRead() functions. They operate at 5 volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have specialized functions:

• Serial: 0 (RX) and 1 (TX):  Used to receive (RX) and transmit (TX) TTL serial data. These pins are connected to the corresponding pins of the ATmega8U2 USB-to-TTL Serial chip.
• External Interrupts: 2 and 3. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
• PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with the analogWrite() function.
• SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI communication using the SPI library.
• LED: 13. There is a built-in LED connected to digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it’s off.

The Uno has 6 analog inputs, labeled A0 through A5, each of which provide 10 bits of resolution (i.e. 1024 different values). By default they measure from ground to 5 volts, though is it possible to change the upper end of their range using the AREF pin and the analog Reference() function. Additionally, some pins have specialized functionality:

• I2C: A4 (SDA) and A5 (SCL):  Support I2C (TWI) communication using the Wire library.

There are a couple of other pins on the board:

• AREF:  Reference voltage (0 to 5V only) for the analog inputs. Used with analogReference().
• Reset: Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board.

See also the mapping between Arduino pins and ATmega328 ports.

Package Include:

• 1 x Arduino Uno R3 Microcontroller ATmega328 SMD Chip Version With USB Cable