Specifications：

• Two wire I2C interface
• Hour : Minutes : Seconds AM/PM
• Day Month, Date – Year
• Leap year compensation
• Accurate calendar up to year 2100
• DS1307 based RTC with CR2032 battery (Battery included)
• 1Hz output pin
• 56 Bytes of Non-volatile memory available to user
• Size: 28x27x8.4mm

Features :

• Two-wire I2C interface
• Hour: Minutes: Seconds AM/PM
• Leap year compensation
• Accurate calendar up to the year 2100
• Consumes Less than 500nA
• 1Hz output pin
• 56 Bytes of Non-volatile memory available to the user
• 4KB of serial electrically erasable and programmable read-only memory (EEPROM)
• Embed DS18B20 temperature sensor interface with the pull-up resistor.

Pin Description of DS1307:

• Pin 1, 2: Connections for standard 32.768 kHz quartz crystal. The internal oscillator circuitry is intended for operation with a crystal having a specified load capacitance of 12.5pF. X1 is the input to the oscillator and can alternatively be connected to an external 32.768 kHz oscillator. The output of the internal oscillator, X2 is drifted if an external oscillator is connected to X1.
• Pin 3: Battery input for any standard 3V lithium cell or another energy source. Battery voltage should be between 2V and 3.5V for suitable operation. The nominal write-protect trip point voltage at which access to the RTC and user RAM is denied is set by the internal circuitry as 1.25 x VBAT nominal. A lithium battery with 48mAhr or greater will backup the DS1307 for more than 10 years in the absence of power at 25ºC. UL recognized to ensure against reverse charging current when utilized as a part of conjunction with a lithium battery.
• Pin 4: Ground.
• Pin 5: Serial data input/output. The input/output for the I2C serial interface is the SDA, which is the open drain and requires a pull-up resistor, allowing a pull-up voltage to 5.5V. Regardless of the voltage on VCC.
• Pin 6: Serial clock input. It is the I2C interface clock input and is used in data synchronization.
• Pin 7: Square wave/output driver. When enabled, the SQWE bit set to 1, the SQW/OUT pin outputs one of four square-wave frequencies (1Hz, 4 kHz, 8 kHz, and 32 kHz). This is also an open drain and requires an external pull-up resistor. It requires the application of either Vcc or Vb at to operate SQW/OUT, with an allowable pull-up voltage of 5.5V and can be left floating, if not used.
• Pin 8: Primary power supply. When the voltage is applied within normal limits, the device is fully accessible and data can be written and read. When a backup supply is connected to the device and VCC is below VTP, read and writes are inhibited. However, at low voltages, the timekeeping function still functions.

Specification:

• Working voltage: 5v
• Two wire I2C interface
• Hour : Minutes : Seconds AM/PM
• Day Month, Date – Year
• Leap year compensation
• Accurate calendar up to year 2100
• Consumes Less than 500nA in Battery-Backup
• Battery included
• 1Hz output pin
• 56 Bytes of Non-volatile memory available to user
• provides 32,768 bits(4KB) of serial electrically erasable and programmable
• read only memory (EEPROM)
• Embed DS18B20 temperature sensor interface with the pull-up resistor
• Dimensions: 28mm x 25mm x 8mm

Features:

• This is the DS1307 Real Time Clock developed by one of our designers.
• Two-wire I2C interface.
• Hour: Minutes: Seconds AM/PM.
• Day Month, Date – Year.
• DS1307 based RTC with LIR2032 battery (Battery include).
• 1Hz output pin.
• Consumes less than 500nA in battery backup mode with oscillator running
• Available in 8-pin DIP or SOIC
• Underwriters Laboratory (UL) recognized
• Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap-year compensation valid up to 2100
• 56-byte non-volatile RAM for data storage
• 56 Bytes of Non-volatile memory available to the user.
• The DS1307 is accessed via the I2C protocol.
• The module comes fully assembled and pre-programmed with the current time.

Package Includes:

• 1 x DS1307 1307 RTC I2C With Battery Real Time Clock Module With AT24C32 EEPROM For Arduino Tiny RTC